CATEGORII
Lift African Black Wood High-End

YAMAMOTO

AL-2

Lift African Black Wood High-End

Unic distribuitor Premiera absoluta
Made in Japan BEST BUY
1,399.00 RON (TVA inclus) Compara
Cantitate:
Stoc:DISPONIBIL
YAMAMOTO - Artistul desavarsit, creator al unor amplificatoare cu lampi cu faima mondiala, pasionatul
de analog cu accesorii pentru pick-up de o calitate premium, apare in Romania pentru iubitorii de muzica
adevarata si emotii rafinate, incepand cu Aprilie 2016.

Fabricate manual, exclusiv in Japonia, YAMAMOTO va vor completa sistemele audio intr-un mod unic,
cu sarm si calitate de clasa mondiala.

AL-2 is the arm lifter unit which adopted a large-sized oil pressure cylinder 16mm in diameter.
The African blackwood was adopted as the sleeve of an attachment part.
An arm can be smoothly taken up and down by operating a larger lever.
When raising a lifter, it goes up for a short time, When taking down, it gets down slowly by oil pressure.
The arm to which an arm lifter is not attached.
Please use for the player with which operation of the lifter became poor.
A crack will be attached to a record if an arm is taken up and down manually, a phonograph needle may be damaged.
Such a trouble can be prevented if an arm lifter is used.
Since this AL-2 lifter unit can carry out every another alone, combining with almost all players is possible.
Refer to the following (attached) figure for directions for use.
Attention : The sleeve part of this product is made of wood. Please be careful not to tighten a cylinder fixed screw too much.
Specifications
The directions for arm lifter unit AL-2
(1) Put a record on the turntable of a record player first,
It is in the state which attached the cartridge of use on an arm,
The needle point brings to the position of the maximum inner
circumference of a record board
It installs so that the range in which the lifter operates as shown in
a lower figure may cover arecordboard top

Height adjustment
A height adjustable screw adjusts using an attached hexagon wrench
so that it may become an upper 5 - 10 mm position of a record board,
after the needle point has raised the lift lever
Since not much big power is not applied to a lifter section, it is not
necessary to bolt a height adjustable screw strongly
The sleeve of a main part should keep in mind that it may damage if
it fastens not much strongly, since it is a product made from an ebony
(2) If the position and height of a lifter unit are decided, fix to the position
using an attached tapping screw or bolt
You may use double-stick tape for fixation
However Please keep in mind that there is a case where it becomes impossible
to remove finely when removing

Height adjustment of this machine is set in the position of the lower part of an
arm pipe, It can adjust from a player board to 39 mm - 53 mm
In asking, please confirm the height of the arm of a player in use

AL-2 Outside Dimension
Oil pressure cylinder: 16 mm in diameter
Diameter of a bottom of a stand section: 38 mm
The length of a lever: 58 mm
Whole height when raising a lever: 60 mm
Arm rest part length: 33 mm
Amount of lifts:
Height of about 3 mm
Lift part: The bottom to 38 - 53 mm adjustment is possible
Color: wood
Producator: Produs:
Imagine
Lift African Black Wood High-End
Produs YAMAMOTO
Lift African Black Wood High-End
AL-2
Descriere YAMAMOTO - Artistul desavarsit, creator al unor amplificatoare cu lampi cu faima mondiala, pasionatul
de analog cu accesorii pentru pick-up de o calitate premium, apare in Romania pentru iubitorii de muzica
adevarata si emotii rafinate, incepand cu Aprilie 2016.

Fabricate manual, exclusiv in Japonia, YAMAMOTO va vor completa sistemele audio intr-un mod unic,
cu sarm si calitate de clasa mondiala.
Specificatii Specifications
The directions for arm lifter unit AL-2 (1) Put a record on the turntable of a record player first, It is in the state which attached the cartridge of use on an arm,
The needle point brings to the position of the maximum inner
circumference of a record board
It installs so that the range in which the lifter operates as shown in
a lower figure may cover arecordboard top
Height adjustment
A height adjustable screw adjusts using an attached hexagon wrench
so that it may become an upper 5 - 10 mm position of a record board,
after the needle point has raised the lift lever
Since not much big power is not applied to a lifter section, it is not
necessary to bolt a height adjustable screw strongly
The sleeve of a main part should keep in mind that it may damage if
it fastens not much strongly, since it is a product made from an ebony
(2) If the position and height of a lifter unit are decided, fix to the position
using an attached tapping screw or bolt
You may use double-stick tape for fixation
However Please keep in mind that there is a case where it becomes impossible
to remove finely when removing

Height adjustment of this machine is set in the position of the lower part of an
arm pipe, It can adjust from a player board to 39 mm - 53 mm
In asking, please confirm the height of the arm of a player in use

AL-2 Outside Dimension
Oil pressure cylinder: 16 mm in diameter
Diameter of a bottom of a stand section: 38 mm
The length of a lever: 58 mm
Whole height when raising a lever: 60 mm
Arm rest part length: 33 mm
Amount of lifts:
Height of about 3 mm
Lift part: The bottom to 38 - 53 mm adjustment is possible Color: wood
Premii
Preţ: 1,399.00 RON (TVA inclus)
Disponibilitate Disponibil
REVIEWS CLIENTI
Adauga review
Ascunde review

Spune-ţi opinia

Numele tău:


Numarul de telefon:


Email-ul:


Opinia ta: Notă: Codul HTML este citit ca şi text!

Nota: Rău           Bun

Introduceţi codul din imagine: